5.0(277 REVIEWS)
  • Mon: 8:00 am-6:00 pm
  • Tue: 8:00 am-6:00 pm
  • Wed: 8:00 am-6:00 pm
  • Thu: 8:00 am-6:00 pm
  • Fri: 8:00 am-6:00 pm
  • Sat: Closed
  • Sun: Closed
1101 California Dr Burlingame, CA 94010-3505
Schedule Appointment
(650) 343-4594

Toyota

Home » Toyota

  • 2006 Toyota RAV4

    Toyota RAV4
    Mileage
    129,944
    Service Date
    8/22/2025
    Services Performed
    • Customer approved to mount and balance all 4 tires including the spare tire. Torque lug nuts to specification.
    • Remove and replace all 5 TPMS sensors due to current sensors having no battery life. Fill tire to specification and program all 5 TPMS sensors.
    • Customer approved to replace front brake pads, rotors, and calipers. Removed brake caliper along with caliper bracket to allow rotors to be removed. Cleaned hub surface prior to installing new rotors. Install bracket with new brake pads. Install new brake caliper, torque mounting bolts to specification along with brake hose. Replaced brake fluid at the same time. Pump brakes and bleed air out of the system. Drive vehicle to help seat in new brake surfaces.
     
    LONNIE L. gave our service a 5 star review on 8/23/2025

  • 2007 Toyota Prius

    Toyota Prius
    Mileage
    106,717
    Service Date
    6/16/2025
    Services Performed
    • Confirmed customer complaint, both headlamps are different intensities. Both headlamp bulbs both different brands which can causing different intensities. Need to replace one bulb so the brands are the same. Tail light bulb needs to be replaced at this time due to being burnt out. Customer approved to remove and replace the right headlamp. Installed Philips bulb to match other Philips bulb already on vehicle. Verified both headlamps are at the same intensity along with the right side tail lamp functioning properly. After headlights have been turned on for awhile and get hot, intensity changes between both lights (left side is dimmer than the right side). Customer needs to return to inspect the left side ballast for a cause.
    • Confirmed customer complaint, TPMS light is on at time of inspection. Inspect all 4 TPMS sensors with scanner. Found that 1 sensor is out of battery along with 2 others being low on battery. Recommend replacing all 4 TPMS sensors at this time.
    • Customer approved to remove, replace, and program all 4 TPMS sensors. Remove all 4 tires, slightly dismount tire to gain access to TPMS sensor. Remove and replace sensors. Fill tire to specification, torque lug nuts to specification. Use scanner to program all 4 new TPMS sensors. Perform road test, verified TPMS light remains off.
    • Customer approved to remove and replace the left side headlamp ballast. Disconnect top of front fascia to gain access to headlamp and module assemblies. Remove the left side headlamp assembly so ballast can be removed. Remove ballast cover, remove ballast (module) from housing. Upon further inspection, found that cable and socket going from ballast cover to ballast is corroded, need to replace cover and cable at this time. Secure new ballast to headlamp assembly. Installed new bulb at the same time (both bulbs are now new). Secure ballast cable along with cover and cable to headlamp assembly. Re-install headlamp assembly, secure mounting bolts and cables. Re-secure front fascia. Turn on headlights and verify both headlamps remain at same intensity over time.
     
    DAN V. gave our service a 5 star review on 6/18/2025

  • 2007 Toyota Prius

    Toyota Prius
    Mileage
    146,740
    Service Date
    5/30/2025
    Services Performed
    • SET TIRE AIR PRESSURES – Front: 35 psi Rear: 33 psi FRONT BRAKES – 80% REAR BRAKES – 40% (Drums) BATTERY – Passed load test (9V) BELTS – OK HOSES – OK AIR FILTER – OK CABIN FILTER – OK LIGHTS – OK WIPERS – OK SHOCKS/STRUTS – OK COOLANT PROTECTION – OK (-50F) TRANSMISSION FLUID CONDITION – OK
    • Customer approved to remove and replace leaking water pump along with replacing the drive belt. Release belt tensioner so belt can be removed along with the idler pulley. Inspect idler pulley for noise to replace if needed. Disconnect cooling hoses from water pump and drain coolant from the system. Remove and replace water pump assembly with new gasket, clean surrounding area of coolant residue during this process. Secure mounting bolts and cooling hoses to new water pump. Secure new drive belt, verify new drive belt is routed properly, secure belt by tightening belt tensioner. Fill vehicle with new coolant, bleed air out of the system. Start engine, verified vehicle runs smoothly at operating temperature with no leaks present.
     
    THOMAS A. gave our service a 5 star review on 5/31/2025